Name: Castolin Eutectic Gmbh
Telephone: +49 6192 4030

Recommended products

Product description	Properties	Applications	Get a quote
Image Eutalloy RW PE 8050 Eutalloy RW PE 8050 is a self-fluxing NiCrBSi alloy with medium hardness, its superb wetting properties make the powder ideal for protective coatings on a variety of base materials like steel, stainless steel and cast iron. Deposits from Eutalloy RW PE 8050 are easy to machine. In addition to good resistance to various wear types like impact and friction they provide excellent corrosion resistance. The coatings are used for working temperatures up to 700°.	Apparent density: ~ 4.5 g/cm3 Melting range: ~ 1050 – 1110°C Hardness: typ. 51 HRC hardness depends on spray parameters and may vary	Restoration of ancient cast iron Coating of glass plungers, repair of glass moulds Hardfacing of connector pins from oil/gas extraction Protection of hydraulic components and shafts	Get a quote
Image Eutalloy RW PE 8097 Eutalloy RW PE 8097 is a NiCrBSi alloy with high hardness. Its specification is modified with molybdenum to achieve better resistance to friction and corrosion compared to other NiCrBSi alloys. Due to chemical composition Eutalloy RW PE 8097 shows a high viscosity during fusing, the material stays on edges and does not run away. Coatings from this powder provide an excellent protection against waste and salt water as well as against most industry atmospheres. The maximum operating temperature is about 700°C.	Apparent density: ~ 4.4 g/cm3 Melting range: ~ 970 – 1070°C Hardness: typ. 58 HRC hardness depends on spray parameters and may vary	Coating of casting rolls in steel industry Hydraulic cylinder for on- and offshore applications Coating of protective couplings Protection of wear and seal sleaves Hardfacing of injection needle valves	Get a quote
Image Eutalloy RW PE 8902 Eutalloy RW PE 8902 is a mix of 65% nickel based self-fluxing powder with 35% tungsten carbides. The embedded carbides considerably improve wear, impact and adhesion resistance compared to the matrix only. Coatings from Eutralloy RW PE 8902 provide a good protection against corrosion from sea- and wastewater and against abrasive wear by fine to medium size particles. They show only low crack sensitivity when fusing. The alloy can be used at temperatures up to 500°C and is suitable for polishing.	Apparent density: ~ 4.6 g/cm3 Melting range: ~ 970 – 1200°C, Matrix only Hardness: typ. 760 HV hardness depends on spray parameters and may vary	Repair of wear parts from blenders for cement and others Coating of knife edges from breaker teeth and from agricultural equipment Hardfacing of feed rollers which require surfaces with high grip	Get a quote
Image Eutalloy RW PE3309 Nickel-base Hardfacing Alloy	Eutalloy RW PE 3309 is a water atomized NiCrBSi alloy with high hardness and low metal friction. In addition to good resistance to varies wear types like rolling and sliding wear it provides excellent protection against corrosion, oxidation and scaling.	Coating of shafts and cylinder rods Repair of conveyor and decanter screws Protection of faucet parts Resurfacing of coal dust separators	Get a quote
Image Eutalloy RW PE3361 Nickel-base Hardfacing Alloy	Eutalloy RW PE 3361 is a NiCrBSi alloy with high hardness. Its specification is modified with molybdenum to achieve better resistance to friction and corrosion compared to other NiCrBSi alloys. Due to chemical composition Eutalloy RW PE 3361 shows a high viscosity during fusing, the material stays on edges and does not run away.	Coating of casting rolls in steel industry Hydraulic cylinder for on- and offshore applications Coating of protective couplings Protection of wear and seal sleaves Hardfacing of injection needle valves	Get a quote
Image Eutalloy RW PE78445			Get a quote

Product description	Image Eutalloy RW PE 8050 Eutalloy RW PE 8050 is a self-fluxing NiCrBSi alloy with medium hardness, its superb wetting properties make the powder ideal for protective coatings on a variety of base materials like steel, stainless steel and cast iron. Deposits from Eutalloy RW PE 8050 are easy to machine. In addition to good resistance to various wear types like impact and friction they provide excellent corrosion resistance. The coatings are used for working temperatures up to 700°.	Properties	Apparent density: ~ 4.5 g/cm3 Melting range: ~ 1050 – 1110°C Hardness: typ. 51 HRC hardness depends on spray parameters and may vary	Applications	Restoration of ancient cast iron Coating of glass plungers, repair of glass moulds Hardfacing of connector pins from oil/gas extraction Protection of hydraulic components and shafts	Get a quote
Product description	Image Eutalloy RW PE 8097 Eutalloy RW PE 8097 is a NiCrBSi alloy with high hardness. Its specification is modified with molybdenum to achieve better resistance to friction and corrosion compared to other NiCrBSi alloys. Due to chemical composition Eutalloy RW PE 8097 shows a high viscosity during fusing, the material stays on edges and does not run away. Coatings from this powder provide an excellent protection against waste and salt water as well as against most industry atmospheres. The maximum operating temperature is about 700°C.	Properties	Apparent density: ~ 4.4 g/cm3 Melting range: ~ 970 – 1070°C Hardness: typ. 58 HRC hardness depends on spray parameters and may vary	Applications	Coating of casting rolls in steel industry Hydraulic cylinder for on- and offshore applications Coating of protective couplings Protection of wear and seal sleaves Hardfacing of injection needle valves	Get a quote
Product description	Image Eutalloy RW PE 8902 Eutalloy RW PE 8902 is a mix of 65% nickel based self-fluxing powder with 35% tungsten carbides. The embedded carbides considerably improve wear, impact and adhesion resistance compared to the matrix only. Coatings from Eutralloy RW PE 8902 provide a good protection against corrosion from sea- and wastewater and against abrasive wear by fine to medium size particles. They show only low crack sensitivity when fusing. The alloy can be used at temperatures up to 500°C and is suitable for polishing.	Properties	Apparent density: ~ 4.6 g/cm3 Melting range: ~ 970 – 1200°C, Matrix only Hardness: typ. 760 HV hardness depends on spray parameters and may vary	Applications	Repair of wear parts from blenders for cement and others Coating of knife edges from breaker teeth and from agricultural equipment Hardfacing of feed rollers which require surfaces with high grip	Get a quote
Product description	Image Eutalloy RW PE3309 Nickel-base Hardfacing Alloy	Properties	Eutalloy RW PE 3309 is a water atomized NiCrBSi alloy with high hardness and low metal friction. In addition to good resistance to varies wear types like rolling and sliding wear it provides excellent protection against corrosion, oxidation and scaling.	Applications	Coating of shafts and cylinder rods Repair of conveyor and decanter screws Protection of faucet parts Resurfacing of coal dust separators	Get a quote
Product description	Image Eutalloy RW PE3361 Nickel-base Hardfacing Alloy	Properties	Eutalloy RW PE 3361 is a NiCrBSi alloy with high hardness. Its specification is modified with molybdenum to achieve better resistance to friction and corrosion compared to other NiCrBSi alloys. Due to chemical composition Eutalloy RW PE 3361 shows a high viscosity during fusing, the material stays on edges and does not run away.	Applications	Coating of casting rolls in steel industry Hydraulic cylinder for on- and offshore applications Coating of protective couplings Protection of wear and seal sleaves Hardfacing of injection needle valves	Get a quote
Product description	Image Eutalloy RW PE78445	Properties		Applications		Get a quote

Subscribe to Eutalloy RW 2 step

Find your technical expert

Get in touch

Product Type

Coating

Welding

Brazing

Wear Parts

Cutting

Product name

Recommended products

Castolin Eutectic

Contact us