Перейти к основному содержанию
Отрасль

Горнодобывающая промышленность

Эксперты в области разведки, добычи и переработки.

Choose a category

shutterstock_162274277_drilling drill ground-min

Процесс бурения с использованием мощных вращающихся инструментов

Бурение
shutterstock_162274277_drilling drill ground-min

Буровые инструменты работают с абразивными материалами различной твердости, текстуры и размеров, такими как гранит, кварц, базальт, гравий и т.д. Основные функции этих инструментов варьируются в зависимости от того, выполняется ли работа путем ударного дробления плотных грунтовых слоев, которые являются менее расщепляемыми, или путем бурения и транспортировки посредством вращения менее плотного и относительно расщепляемого материала.

Эти инструменты для ударного бурения (буровые штанги) обычно испытывают значительные ударные нагрузки и истирание. По этой причине выбор сплавов ориентирован на упрочняющиеся наклепом, которые устойчивы к деформации.

shutterstock_137398853_shearer_mining

Дать инструментам вторую жизнь

Буровые инструменты
shutterstock_137398853_shearer_mining

Для инструментов, осуществляющих проходку путем вращения (шнек, буровая штанга), основным типом износа является истирание в сочетании со слабым давлением на поверхность. Предпочтение необходимо отдавать сплавам обладающим хорошей износостойкостью против средних ударов и истирания под воздействием слабого давления.

shutterstock_294917552_augers for drilling-min

Сплав для защиты от ударов и истирания

Шнеки
shutterstock_294917552_augers for drilling-min

Каждый инструмент специфичен, а условия эксплуатации зависят от характера грунта. Тем не менее, в основном наблюдаются два возможных применения:

  • Защита от износа истиранием при помощи использованием чугуна с высоким содержанием хрома, в тех случаях, когда инструменты не подвергаются сильному удару.
  • Часто эти инструменты подвержены ударам, которые разрушают защитные покрытия. В этом случае выбирается сплав c содержанием карбидов вольфрама и матрицей, которая менее чувствительна к удару.
 Laser cladded wear liners are the ultimate choice for high wear resistance in a lightweight design.​

CUTTING-EDGE LASER CLAD WEAR LINERS

CDP® LaserMax​
 Laser cladded wear liners are the ultimate choice for high wear resistance in a lightweight design.​

Avoid equipment failures and drastically reduce downtime with the most lightweight wear protection available with superior surface hardness.  CDP LaserMax is the optimal choice for protecting mining parts exposed to high wear with minimum component stress, including mine ventilation fans, mine skips, conveying systems, and certain material handling systems.​

​Our laser clad wear plate is metallurgically bonded with wear-resistant proprietary alloys in an ultra-thin design.  The powder becomes the sacrificial layer on the base plate, offering maximum protection at minimum weight.​

  • ​Superior surface hardness ​
  • Ease of handling and installation​

  • Improved mine safety and work environment​

  • Light-weight alternative with reduced energy consumption​

  • Increased sustainability

Lafarge Wössingen Brecher 09.02.09 008

Подвергается истиранию

Ротор дробилки
Lafarge Wössingen Brecher 09.02.09 008

Ротор является основным элементом дробилки, он снабжен молотками, закрепленными при помощи крепежных элементов. Диски, сваренные механизированным способом, подвержены истиранию из-за воздействия абразивных частиц на внешние части диска. На этих деталях, а также на боковых поверхностях рекомендуется нанести защитное покрытие.

chrome white iron parts in high wear areas protect chutes and buckets from abrasion and impact​

ENHANCE OVERALL WEAR LIFE WITH CASTOCHROME CASTINGS

Wear Castings Applications 
chrome white iron parts in high wear areas protect chutes and buckets from abrasion and impact​

Fixed Plant​

  • Mill feed & discharge chutes​

  • Transfer & load-out chutes​

  • Skip discharge chutes​

  • Surge bins and receiving hoppers​

  • Conveyor skirt liners​

  • Vibratory and grizzly feeders​

  • Apron & pan feeders​

​Mobile Plant:​

  • Dragline buckets​

  • Electric rope shovels​

  • Wheel loader buckets​

  • Dozer blades​

  • Truck boxes​

conveyor_belt

Избегайте повреждений оборудования

Ленточно-цепные конвейеры
conveyor_belt

Ленточно-цепные конвейеры идеально подходят для перемещения таких материалов, как древесина, уголь, известь или отходы, когда требуется изменение высоты, и на очень большие расстояния. К сожалению, абразивность транспортируемого материала отрицательно влияет на срок службы оборудования,

  • изнашивая поверхность конвейера,
  • увеличивая усилия, необходимые для натяжения цепи.

Большую часть времени на линии цепи появляется высокий износ. В результате поверхность больше не становится гладкой, усилия увеличиваются, цепь повреждается, а детали необходимо регулярно заменять, чтобы избежать поломки оборудования.

wss

Износостойкость выше в 4 раза, чем у традиционной закаленной стали

Износостойкие полированные пластины (WSS)
wss

На протяжении многих лет компания Castolin Eutectic занимается защитой поверхностей конвейеров наших заказчиков с помощью широко известных пластин для защиты от износа CDP®.  Полированные пластины из премиальных износостойких плит CDP® также устанавливались, когда требовалась поверхность с низким коэффициентом трения. Сегодня, основываясь на аналогичных примерах, мы предлагаем простые в установке износостойкие пластины WSS, которые защищают линию цепи от сильного истирания и трения. Износостойкие пластины WSS представляют собой композитный материал, изготовленный из мягкой стали и специального износостойкого сплава с низким коэффициентом трения. Для обеспечения хороших скользящих свойств и снижения энергопотребления цепного конвейера поверхность пластины полируется. В результате наши пластины обладают по крайней мере в 4 раза большей износостойкостью, чем традиционная закаленная сталь. Поверхности остаются более гладкими в течение более длительного периода времени, что в конечном счете также уменьшает повреждение цепи. Износостойкие пластины WSS также подходят для машин, которые должны выдерживать высокие нагрузки и вибрации при работе в абразивной среде.

CastoTube pipes ready to be shipped to provide ultimate wear resistance in slurry transportation

BENCHMARK BACKFILL SLURRY WEAR PERFORMANCE​

The CastoTube® Advantage​
CastoTube pipes ready to be shipped to provide ultimate wear resistance in slurry transportation

Where safety meets efficiency and productivity​

  • Benchmark performance | Reduced cost per tonne ownership ​

  • Engineered pipe connections | Efficient retrofit and new installations​

  • Process controlled cladding ensures superior performance ​

  • Technical support | Site-specific wear surveys and performance monitoring ​

  • Mine contractor grade offerings | Ease of installation & impact resistant formula

Engineered, wear resistant pipes for slurry handling in mining and mineral processing

ECONOMICAL WEAR RESISTANT PIPES FOR SLURRY BACKFILL TRANSPORTATION​

MeCaPipe™​
Engineered, wear resistant pipes for slurry handling in mining and mineral processing

MeCaPipe is our economical alternative to CastoTube wear pipes.  MeCaPipe incorporates the high-performing MeCaTeC lining technology to offer an alternative solution for general slurry applications. Combined with CastoTube, MeCaPipe can meet specific client requirements to provide the adequate level of protection against abrasion, erosion and corrosion. For a seamless wear performance, the lining thickness is typically selected based on the finished ID to match the existing piping system. ​

​MeCaPipe is engineered to withstand slurry wear and erosion. It outlasts traditional piping materials, minimizing costly changeouts and providing enhanced performance and operational efficiency. MeCaPipe can be easily repaired or relined to prolong life.​

​Our team will work closely with your mine to deliver the right pipe lining solution to optimize your slurry backfill transportation systems.​

​Contact us for an expert wear pipe analysis.​

worker applying a trowel-grade wear compound inside a mining equipment for abrasion and erosion protection

​​​​​​MINE-GRADE WEAR COMPOUNDS FOR ABRASION, EROSION AND CORROSION PROTECTION

Engineered Polymers to Repair, Rebuild & Protect
worker applying a trowel-grade wear compound inside a mining equipment for abrasion and erosion protection

From repair and rebuild to corrosion resistant barrier coatings, MeCaTeC offers an industry-leading range of engineered polymers that will perform in the most demanding mining applications.  MeCaTeC is the ideal solution for quick surface and part repair.  It instantly bonds to the surface with no welding, becoming a sacrificial layer that provides abrasion and erosion protection.  Its cold bonding feature eliminates the need for a Hot Work Permit.​

​MeCaTeC is the ultimate protection layer for the demanding resurfacing requirements. Protect your assets with MeCaTeC!​

​Typical Applications include:​

  • Ceramic tile and rubber lining replacement  ​

  • Cyclones, chutes, bins and transfer points​

  • Pipe elbows and slurry pipes​

  • Slurry pumps​

  • Screw conveyors​

  • Bag house 

Crusher backing compounds are a cost-effective way to protect crushing machines from friction, vibration and wear

HIGH PERFORMANCE CRUSHER BACKING COMPOUNDS

MeCaBack Next-Gen Solution for Crusher Equipment Maintenance​
Crusher backing compounds are a cost-effective way to protect crushing machines from friction, vibration and wear

Crusher backing compounds are a cost-effective way to protect crushing machines from friction, vibration and wear. ​

​Our innovative line of crusher backing compounds is specifically designed to reinforce the liner, fill voids, reduce vibration and eliminate friction in rock crushing heavy machinery.  It is easily applied between both gyratory and cone crusher liners and the crusher body part.​

MeCaBack is an excellent choice of a crusher compound for mining, mineral processing and aggregate equipment including:​

  • Crushing machines​

  • Cone & stone crushers​

  • Grinding mill liners​

  • Backing plates​

  • Lock bushings​

sprayable corrosion and erosion resistant polymer coating for fan blades

PERFECT COMBINATION OF SAFETY, PERFORMANCE AND COST SAVINGS

The MeCaTeC® Advantage​
sprayable corrosion and erosion resistant polymer coating for fan blades
  • Proprietary formula with Kevlar fiber interlocking technology ​

  • Engineered ceramic fillers to maximize wear performance​

  • Optimized packaging for faster mixing during shutdown repairs ​

  • Excellent alternative to replace ceramic tiles and rubber linings​

  • Rapid-cure formula ensures a quick return to service​

  • Easy to apply with trowel, brush, MeCaSpray gun, or airless spray​

  • On-site Technical Support with industry-leading expertise and application know-how

Задать вопрос эксперту

Откройте для себя другие отрасли

Статус

Sorry…This form is closed to new submissions.
Распространение наших передовых технологий в сфере сварки, твердой пайки и нанесения покрытий
Брошюры
CDP® 4624
Wear parts English
CDP® 4624

CDP® XuperWave 4624 DXW is the ideal wearplate for the application where the right balance between price and service life is required

Wear parts English
CDP® 1001

Readily weldable base plate for fast installation